$555.00
Sold Out
The Fono MC is an exceptionally high quality MC phono stage designed to maximise the potential of any MC cartridge. Although designed to compliment Rega moving coils, adjustability is available via dip switches conveniently placed on the rear panel.
The Rega Fono MC is an exceptionally high quality MC phono stage designed to maximise the potential of any MC cartridge. Although specifically to compliment the latest Rega range of moving coils you will find full adjustability for loading is available via dip switches conveniently placed on the rear panel with two different gain settings located on the back panel making the Fono MC compatible with most low output MC cartridges. The Rega Fono MC has been designed to be effective, easy to use, and above all, to reproduce music. The Fono MC uses the Linear Systems low noise LSK389 FET in an all discrete input stage where low noise and linearity are vitally important to get the best from an MC cartridge. Because of the high input impedance of FET, the loading effects of the amplifier circuit are minuscule and do not affect the performance of the cartridge. A MUSE operational amplifier is used in the RIAA equalization amplifier. Polypropylene capacitors have been used in the signal path and in the RIAA equalization circuits. There is selectable input loading for both resistance and capacitance along with two different gain settings located on the back panel making the Rega Fono MC compatible with most low output MC cartridges. The aesthetic design of the Rega Fono MC was as important as the quality of its electrical capabilities, so it benefits from the same aluminium case as the Rega TTPSU and Fono MM amplifier, giving it a design which offers a familiar feel and moreover brings it in line with its illustrious bigger brothers. The new Fono MC circuit resulted from the design work carried out on the Aria phono amplifier. The Fono disk stage is designed to amplify the signal from a moving coil cartridge to a level which can feed into a 200mV line level input on a standard hi-fi amplifier. Rega Fono Specifications Output impedance = 200Ω Recommended minimum output load resistance = 5K Frequency response (50KΩ output load) = 13Hz (-3dB) to 100KHz (-0.3dB) RIAA accuracy (50KΩ output load) = Better than +/-0.2dB 100Hz to 100KHz Power requirements = 24V AC at 150mA maximum. Only to be used with Rega PS1. Input sensitivity (for 200mV output) 4 off = 133uV 4 on = 67uV Input loading resistance 1 and 2 off = 400Ω 1 on = 100Ω 2 on = 150Ω 1 and 2 on = 70Ω Input loading capacitance 3 off = 1000pF 3 on = 4300pF Gain (at 1KHz) 4 off = 63.5dB 4 on = 69.5dB Maximum input level (at 1KHz) 4 off = 6.7mV 4 on = 3.4mV Load settings for adjustable MC stages Impedance -100ohm Capacitance – 1000pF Gain setting – High (‘On’ position for Rega phono stages)
None, Exact, Ania Moving Coil, Ania Pro Moving Coil
PHONOSTAGE/PRE-AMP
General
Power Supply – AC120 V, 60 Hz Power Consumption – 14 W Approx. 0.2W (Standby) Dimensions (W x H x D) – 17-27/32 x 6-13/16 x 14-21/32 inch Weight – Approx. 39.7lbs Accessories – Turntable, Turntable sheet, Dust cover, EP record adaptor, Balance weight, Auxiliary weight(S), Auxiliary weight(L), Head shell, Overhang gauge, Screw set for cartridge, PHONO cable, PHONO earth lead, AC power supply cord, Screw set for turntable, Owner’s Manual
Terminals
Audio Output – PHONO (Pin Jack) x 1, EARTH TERMINAL x 1
Tonearm Section
Type – Universal Static Balance Effective Length – 230mm (9-1/16″) Overhang – 15mm (19/32″) Tracking Error Angle – Within 2° 32’ (at the outer groove of 30cm(12″) record), Within 0° 32’ (at the inner groove of 30cm(12″) record) Offset Angle – 22° Arm-height Adjustment Range – 0 – 6 mm Stylus Pressure Adjustment Range – 0 – 4 g (direct reading) Head Shell Weight – Approx. 7.6 g Applicable Cartridge Weight Range – (without auxiliary weight) 5.6 – 12.0g 14.3 – 20.7g (including headshell) (with small auxiliary weight) 10.0 – 16.4g 18.7 – 25.1g (including headshell) (with large auxiliary weight) 14.3 – 19.8g 23.0 – 28.5g (including headshell) Cartridge Mounting Dimension – JIS 12.7 mm Interval Head Shell Terminal Lug – 1.2 mm φ 4-pin Terminal Lug
Turntable Section
Type – Direct Drive Manual Turntable Turntable Speeds – 33 1/3, 45, 78 rpm Adjust Range – ±8%, ±16% Starting Torque – 3.3 kg･cm (2.8 lb-in) Build-up Characteristics – 0.7 s. from standstill to 33 1/3 r/min Wow And Flutter – 0.025% W.R.M.S. (JIS C5521) Rumble – 78dB (IEC 98A Weighted) Turntable Platter – Brass and Aluminum diecast combined, Diameter 332mm (13-5/64″), Weight：About 3.6kg (7 15/16 lb) (Including rubber sheet)
© 2025 Blink High End. All Rights Reserved.